See Closing the System. Replace the cooling shroud and computer cover, and then reconnect the computer and peripherals to their AC power sources and turn them on. Remove the front bezel. See Figure3-25. http://www.dell.com/support/Article/SLN296868
Unlatch and pull each hard-disk drive 25-mm (1-inch) out of its slot. Install the CPU_1 cooling shroud blank. Enter the System Setup program and if the time and date are still incorrect, see Getting Help for instructions on obtaining technical assistance. Remove the cooling shroud.
NOTE: Keep this bracket in case you need to remove the expansion card. CAUTION: Use caution when handling the fan until the fan blades stop spinning. Cooling Shroud Replacement To replace the cooling shroud, perform the following steps: Hook the upper edge of the large opening on the end of the cooling shroud over the top of How To Open Alienware Aurora Case On the opposite side of the back panel, grasp the extended head of the fastener and pull the fastener completely out of the back panel, as shown in Figure 16.
Install the expansion card: If the expansion card is full length, align its front edge with the front card guide. The interposer card provides enhanced functionality that makes the SATA hard drive usable in some storage systems. See FigureA-3 for the location of the expansion card slots. https://books.google.com/books?id=eeEsanJ1bZwC&pg=PA18&lpg=PA18&dq=Cooling+components+available+to+install+on+a+Dell&source=bl&ots=c8FT7lWM-f&sig=jxuJCmKYizvWQe3S26_KUmrVkEM&hl=en&sa=X&ved=0ahUKEwiJ3qHB287RAhXFBZoKHWbuB Removing the VRM CAUTION: Only trained service technicians are authorized to open the system cover and access any of the components inside the system.
See Opening the System. Alienware X51 Cmos Reset Repeat step 3 through step 7 of this procedure to install the remaining memory modules. Replace the right-side computer cover and reconnect the system to AC power. Insert the SATA hard drive into the SATAu hard-drive carrier with the connector end of the drive at the rear.
See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. While pulling the release pin, slide the riser board away from the expansion card openings. How To Open Alienware X51 Case Install each hard-disk drive into its slot and close its latch. How To Open Alienware Area 51 Case Back to Contents Page Removing and Replacing Parts: Dell PowerEdge 2400 Systems Service Manual Overview SCSI Backplane Boards Recommended Tools Cooling Shroud Safety FirstFor You and Your Computer Cooling Fans Protecting
NOTICE: Never remove the memory cooling shroud without first powering down the system. Locate the memory module sockets on the system board. NOTICE: See "Protecting Against Electrostatic Discharge." Turn off the system, including any attached peripherals, and disconnect the AC power cable from its power source. Drives Figure 8 shows an example of drive hardware that can be installed in the computer. How To Open Alienware Aurora R5 Case
Remove the power supply blank only if you are installing a second power supply. Slide the riser board toward the expansion card openings until you feel the riser-board release pin snap into place. Disconnect the cable from the back of the diskette drive. Source See Figure3-4.
Reinstall the SAS controller daughter card. How To Open Alienware Area 51 R2 Place one end of the heat sink under the retention module base tab, and lower the heat sink onto the processor until the heat sink snaps securely in the retention module Open the drive carrier handle to release the carrier (see Figure12).
See Installing the Cooling Shroud. See the documentation that came with the card for information about its cable connections. See "Closing the System" in "Troubleshooting Your System." Reconnect the system to the electrical outlet, and turn on the system and attached peripherals. Alienware D05s Specs To replace the control panel assembly, slide the slots in the assembly over the upper chassis hooks (see Figure 6), then slide the assembly down until its bottom edge engages the
Insert the module into the connector, and carefully press each end of the module into place. See your System Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. When the front of the card is fully seated, the plastic standoff snaps over the edge of the card. have a peek here Front Fan Replacement To install the replacement fan to the inner bulkhead beneath the drive bays at the chassis front, perform the following steps.
Hot-Pluggable Power Supply Removal 1 Power supplydistribution board(PSDB) 2 Power supply 3 Latch on handle To remove a hot-pluggable power supply with the system operating, perform the following steps. Place the card-edge connector in the expansion-card connector and press down firmly. Removing a Memory Module CAUTION: Only trained service technicians are authorized to open the system cover and access any of the components inside the system. Pull the power supply 25 mm (1 inch) away from its back connector and wait 10 to 20 seconds to allow energized components to dissipate.
ThelnsomniacGamer 45.337 visualizaciones 9:22 Video Card Upgrade for the Dell Dimension 2350 - Duración: 14:48.